Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Blog Article
Were you in search of information and facts concerning How to Install a Bathtub?
Installing a tub isn't exactly brain surgery, however it does call for strong plumbing, carpentry, as well as sometimes, tiling abilities. Changing an old tub with a new one is likewise a moderately hard project. If the old tub is conveniently available, the project can move immediately; if you have to open a wall to remove the old bathtub and place the new bath tub, the task is much harder. In either case, the job is within a home handyman's skills, although you will certainly need an assistant to vacate the old tub and also set in the brand-new one. See to it you have qualified yourself for the job as well as are comfortable trying it. Instead of hiring a contractor to take over a halfway-completed task, it is far better to consider using one before you start. Chances are you may require an expert plumber to make tube connections.
This short article will certainly help you install a new bath tub in your washroom if you have actually already acquired a brand-new bathtub and do not require to transform the setup of your previous water system pipes.
Your devices and also product list should consist of the following:
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your installment, after that the first thing you should do is separate the water supply. After doing so, turn on the taps to drain pipes any type of water continuing to be in the system. The procedure of eliminating the existing taps can be fairly problematic as a result of the limited access that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a cloth all set for the remaining water that will certainly originate from the pipelines. Once the supply pipelines have actually been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from transforming throughout this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any old securing compound.
Before going on to fit the new taps, compare the pipe links on the old taps to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the new faucets are plastic, then you will certainly require a plastic adapter to avoid damages to the string. One end of the connector fits on the plastic tail of the faucet and the other end gives a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly need reducing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, position the faucet in the installing opening in the bath/basin making certain that the washers remain in location between the tap and also the sink. Safeguard the faucet in place with the producer provided backnut. When the tap is safely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical faucet connectors. The previous type needs to be linked to the faucet finishes first, tightening just by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Setting up the Bath tub
Utilizing the two wooden boards under its feet, place the tub in the called for position. The wooden boards are practical in uniformly spreading the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 little points.
The following objective is to make sure that the tub is leveled all round. This can be accomplished by inspecting the level and readjusting the feet on the bathtub until the spirit level reads level.
To set up faucets, fit all-time low of the furthest adaptable faucet connector to the proper supply pipe by making a compression join; after that do the same for the various other tap.
Turn on the water supply and inspect all joints as well as brand-new pipework for leakages as well as tighten them if essential. Load the bathtub and also check the overflow outlet and the normal electrical outlet for leakages.
Lastly, fix the bath paneling as described in the manufacturer's instruction manual. Tiling and also securing around the tub should wait until the tub has been made use of a minimum of when as this will certainly settle it into its final placement.
Planning for the Installation
Firstly, the supporting structure supplied with the bath ought to be fitted (if required) according to the producer's guidelines. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is important to see to it that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets unit to prevent pressure on the bathtub.
Fit the versatile faucet connectors to the bottom of the two faucets using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you use all of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its last setting.
Tiling Around the Tub
In the area where the bath satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to fracture a rigid seal, triggering the water to penetrate the wall between the bath and also the tiling, bring about difficulties with wetness as well as feasible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your components as well as installations. They are marketed in tubes and also cartridges, as well as are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill up the bathtub with water prior to sealing, to allow for the activity experienced when the tub remains in use. The sealant can split fairly early if you do not take into consideration this motion before securing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally quickly available on the marketplace. It is advisable to fit the floor tiles making use of water-resistant or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been shown that editorial on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround from an acquaintance on another web property. Sharing is caring. Helping people is fun. I enjoy reading our article about Tools You Need to Install a New Bathtub .
Stay calm, just ring. Report this page